多刀分板機的上刀片和下刀片形成一組以形成切割單元。他們分別是a、b、c和3組。整個切割過程分為三個階段。甲組刀片先切割電路板的40%，然后乙組刀片再次運行在甲組刀片切割的凹槽上，再次完成40%的切割量。最后，C組刀片切割最后的20%并修剪。由于每次切削量小，與傳統的一次性切削方法相比，切削過程中產生的應力減少了80%以上。分開的電路板的邊緣是平坦和光滑的，并且板表面非常平坦，沒有扭曲或翹曲。
The upper blade and the lower blade of the multi cutter splitter form a group to form a cutting unit. They were group A, group B, group C and group 3. The whole cutting process is divided into three stages. Group a blade first cuts 40% of the circuit board, and then group B blade runs again on the groove cut by group a blade to complete 40% cutting amount again. Finally, group C blades cut the last 20% and trim. Compared with the traditional one-off cutting method, the stress produced in the cutting process is reduced by more than 80% due to the small amount of cutting each time. The edges of the separated boards are flat and smooth, and the board surface is very flat without distortion or warpage.
多刀分板機可以一次分割整塊板材，并且可以上下對接，實現無人操作。不僅安裝方便，而且操作設置簡單，可以節省很多員工、時間和人力。占用空間小，最大限度地節省了操作時間。多刀分板機可同時切割多組刀具，并一次分割整塊板材，從而保證分離后的板材不變形，同時不翹曲，效率高，并嚴格控制變形程度。
The multi cutter board dividing machine can split the whole board at one time, and can be connected up and down to realize unmanned operation. It is not only easy to install, but also easy to set up, which can save a lot of staff, time and manpower. It takes less space and saves operation time to the greatest extent. The multi cutter dividing machine can cut multiple groups of cutting tools at the same time, and divide the whole plate at one time, so as to ensure that the separated plate does not deform and warpage at the same time, with high efficiency and strict control of deformation degree.
多刀分板機采用進口TBI螺桿，定位精度高，刀盤受力小。多刀分板機采用安全性能高的開門保護裝置。多刀分板機可自動送料和切板，效率更高。上下對接紙板機，節省勞動力。多葉片分板機的葉片材料為進口高速鋼。刀片與刀片正面之間的距離至少為3毫米，刀片厚度為0.2毫米，介子尺寸根據印刷電路板的尺寸定制，刀片的使用壽命為10萬次，刀片可反復翻轉研磨重復使用。根據具體情況，鏟刀可以轉動和打磨2-3次。
The imported TBI screw is used in the multi cutter dividing machine, with high positioning accuracy and small force on the cutter head. The door opening protection device with high safety performance is adopted for the multi cutter board splitter. The machine can automatically feed and cut the plate with higher efficiency. Up and down docking paperboard machine, saving labor. The blade material of multi blade plate splitter is imported high speed steel. The distance between the blade and the front of the blade is at least 3mm, and the thickness of the blade is 0.2mm. The size of the meson is customized according to the size of the printed circuit board. The service life of the blade is 100000 times. The blade can be repeatedly overturned, ground and reused. According to the specific situation, the blade can be rotated and polished 2-3 times.
多刀分板機采用多組上、下刀片同時分?jǐn)唷ＴO(shè)備底部安裝有帶可調腳杯的腳輪，方便設備移動，不移動時需要穩定固定。上刀和下刀之間的間隙可根據印刷電路板的V形切割間距進行調整，精度控制在0.1毫米，相鄰兩組刀片之間的間距可在10毫米至25毫米之間調整，所需寬度可快速調整。刀具開始運行，多組刀具同時切割產品，整塊拼版一次分割，產品輸送帶開始運行。產品分割完成后，傳送帶立即停止，以確保產品停留在傳送帶上。
The multi knife plate splitter adopts multiple groups of upper and lower blades to break at the same time. A caster with adjustable foot cup is installed at the bottom of the equipment, which is convenient for the equipment to move. It needs to be fixed stably when it is not moved. The gap between the upper and lower blades can be adjusted according to the V-shaped cutting distance of printed circuit board. The precision is controlled within 0.1 mm. The distance between two adjacent groups of blades can be adjusted between 10 mm and 25 mm. The required width can be adjusted quickly. The tool starts to run, multiple sets of cutters cut the product at the same time, the whole block is divided at one time, and the product conveyor belt starts to run. The conveyor belt stops immediately after the product separation to ensure that the product stays on the conveyor belt.
上述所講解的就是多刀分板機的功能優勢，希望看完能夠?qū)δ兴鶐椭绻胍私飧嚓P(guān)于多刀分板機的功能優勢，歡迎在線咨詢客服或是撥打本公司服務熱線（網站右上角）進行咨詢，我們將竭誠為您提供優質的服務！
The above explanation is the function advantages of the multi knife splitter. I hope it can help you after reading it. If you want to know more about the functional advantages of the multi cutter board splitter, please contact customer service online or call our service hotline (top right corner of the website) for consultation. We will wholeheartedly provide you with high-quality service!
中文版 
English1
